Global PCB Connections: The Future of HDI PCBs
The Shaughnessy Report: The Designer of Tomorrow
Designers Notebook: Impact of Advanced Semiconductor Packaging on PCB Stackup
Reassessing Surface Finish Performance for Next-gen Technology, Part 1
June 26, 2023 | Frank Xu, PhD and Martin Bunce of MacDermid Alpha, and John Coonrod of Rogers Corp.Estimated reading time: 1 minute
Introduction
Over the years, various surface finishes have been successfully utilized, namely organic solderability preservative (OSP), immersion silver (ImAg), immersion tin (ImSn), electroless nickel immersion gold (ENIG), and electroless nickel electroless palladium immersion gold (ENEPIG), as solderable finishes for PCB and package substrates. All these surface finishes have their pros and cons, with no single finish being suited to all applications.
As system designers continue to respond to new performance demands, it can be noted that ENIG/ENEPIG finishes have endured as a leading choice in many advanced applications where reliability is prioritized over cost.
Electroless nickel (EN) deposits have served well as a barrier layer, preventing copper migration to the outer gold or palladium-gold surfaces, and enabling the robust solderability performance of ENIG and ENEPIG finishes. However, the introduction of the 5G mobile network creates a growing demand for smartphones, networking, and wireless connections, all requiring increased “data flow.” The need to reduce the signal loss at higher frequency bandwidth is becoming vitally important. The low conductivity and magnetic properties of EN affect electrical signals as they travel along a conductor’s outer surfaces leading to insertion losses at higher frequencies.
As a result, designers and fabricators are looking for newer-generation surface finishes to meet their performance criteria. EPIG (electroless palladium immersion gold with no EN), silver-gold (Ag-Au), and reducing the EN thickness from traditional ENEPIG, have all gained attention. What follows is a review that compares the performance attributes of the leading candidates for a high-frequency alternative surface finish.
MacDermid Alpha Electronic Solutions has worked in partnership with Rogers Corporation to evaluate the effect of various surface finishes on signal loss with increasing frequency. Together, we subsequently worked to understand and compare other critical-to-quality performance metrics that will guide application-based surface finish selection.
Work Program
We first set out to evaluate the effect of surface finish on signal losses up to 110 GHz using the microstrip test method and a vector network analyzer, with the support of Rogers.
To read this entire article, which appeared in the June 2023 issue of Design007 Magazine, click here.
Share on:
Suggested Items
Designers Notebook: Impact of Advanced Semiconductor Packaging on PCB Stackup
01/07/2025 | Vern Solberg -- Column: Designer's NotebookTo accommodate new generations of high I/O semiconductor packaging, printed circuit board fabrication technology has had to undergo significant changes in both the process methods and the criteria for base material selection and construction sequence (stackup). Many of the new high-function multi-core semiconductor package families require more terminals than their predecessors, requiring a significantly narrower terminal pitch. Interconnecting these very fine-pitch, high I/O semiconductors to the PCB is made possible by an intermediate element referred to as an interposer.
BOOK EXCERPT: The Printed Circuit Designer’s Guide to... High Performance Materials, Chapter 4
01/02/2025 | I-Connect007In Chapter 4, Michael Gay discusses the two main types of copper foil used for PCB boards today: electrodeposited (ED) foil and rolled annealed (RA) foil. He also explains the pros and cons of each, and provides an update of the latest innovations in copper foil technology.
Connect the Dots: Designing for Reality—Solder Mask and Legend
01/02/2025 | Matt Stevenson -- Column: Connect the DotsIn the previous episode of I-Connect007’s On the Line with… podcast, we discussed the strip, etch, and strip process. At this point, we have a functioning board, but we still need to protect the PCB from environmental effects and document the circuit components. This brings us to the solder mask and legend phase of production.
Global PCB Connections: Following DFM Rules Leads to Better Boards
12/18/2024 | Jerome Larez -- Column: Global PCB ConnectionsAs a PCB field applications engineer, ensuring smooth communication between PCB designers and fabricators is one of my frequent challenges. A critical part of that dialogue is design for manufacturing (DFM). Many designers, even experienced ones, often misunderstand or overlook important DFM considerations. They may confuse design rules with manufacturing minimums, leading to technically feasible designs that are difficult or costly to produce. In this column, I will clarify some common DFM guidelines and help designers understand the difference between “design rules” and “minimums” while sharing best practices that will simplify the production process and ensure the highest quality PCB.
Sayonara to the Last Standing Copper Foil Plant in North America
12/17/2024 | Marcy LaRont, I-Connect007In July 2021, PCB007 Magazine published an interview with Michael Coll and Chris Stevens of Nippon Denkai about the new acquisition by Nippon Denkai of the last-standing ED foil manufacturer in North America. The plant in Augusta, Georgia, was formerly owned by Oak Mitsui, Inc. and had been purchased by Nippon Denkai the previous March, after which significant investment was made with the expectation of providing more jobs.