If You Can Define It Right, You Can Design It Right
December 5, 2024 | Andy Shaughnessy, Design007Estimated reading time: 1 minute

Design engineer Chris Young is known for his optimized design process. As lead hardware engineer with Moog Space and Defense Group and owner of Young Engineering Services, Chris collects data like it’s going out of style, and he leaves nothing to chance.
With that in mind, I asked Chris to discuss his views on rules of thumb—which ones work, which ones should be avoided, and how rules fit ideally into the PCB design process.
Andy Shaughnessy: I know that you’ve spent a lot of time and effort over the years dialing in your design process. How do you use rules of thumb in your design cycle?
Chris Young: I use purpose-driven rules of thumb that produce practices that reduce risk and drive a desired outcome. I am much less concerned about using a specific PCB stack-up than producing a solution that works and meets requirements.
Shaughnessy: What are some of the rules of thumb that you use regularly, and why?
Young: Rule No. 1: If you can define it right, you can design it right.
Spend time up front developing requirements that can be used to guide your design to success. The lack of requirements in a project lead to technical ambiguity that is too often stop-gapped with assumptions. These assumptions lead to design errors that result in technical debt or design spins that cost money. The old adage of “measure twice, cut once” still applies. I recommend the INCOSE Guide to Writing Requirements (incose.org) for anyone interested in learning more about developing clear, actionable requirements.
To read this entire conversation, which appeared in the November 2024 issue of Design007 Magazine, click here.
Suggested Items
Ansys Strengthens Collaboration with TSMC on Advanced Node Processes Certification and 3D-IC Multiphysics Design Solutions
04/24/2025 | PRNewswireThrough continued collaboration with TSMC, Ansys announced enhanced AI-assisted workflows for radio frequency (RF) design migration and photonic integrated circuits (PICs), and new certifications for its semiconductor solutions. Together,
Autodesk Donates $4.3 Million to Cornell University to Prepare students for an AI-powered future
04/24/2025 |Autodesk announced a $4.3 million gift to Cornell University’s College of Engineering and College of Architecture, Art, and Planning (AAP) to help prepare students for the future of work in an increasingly AI-driven world. The investment will fund a new Autodesk Cornell Engineering Design and Make Space in Upson Hall.
Driving Sustainability in PCB Design
04/24/2025 | Marcy LaRont, I-Connect007Filbert (Fil) Arzola is an electrical engineer at Raytheon. He’s smart, entertaining, and passionate about PCB design. As it turns out, he’s also passionate about “Mother Earth,” as he calls her. Born and raised in Southern California, he freely admits that he turns the water off when he brushes his teeth and yells at his brother for throwing batteries in the garbage. But when looking at the issue of sustainability and PCB design, he urges his audiences to ponder what sustainability looks like. Can PCB designers, he asks, make any impact on sustainability at all?
Real Time with... IPC APEX EXPO: Silicon Geometry's Signal Integrity Impact on PCBs
04/24/2025 | Marcy LaRont, I-Connect007At IPC APEX EXPO 2025, Kris Moyer addressed the importance of understanding the impact of silicon geometry reduction on signal integrity and PCB performance. Kris says signal integrity considerations are necessary for so many designs today, regardless of clock frequency. He discusses valuable insights from attendees regarding embedded resistor technology and the effects of radiation on smaller silicon features in aerospace applications.
Elementary Mr. Watson: Navigating RF—A Glide Path Approach to Design Success
04/24/2025 | John Watson -- Column: Elementary, Mr. WatsonOn a flight, I can always tell when we begin our descent because that subtle drop in my stomach tells me the altitude has changed. Landing an airplane involves a gradual, precise process called the glide path. It descends at the correct speed and 3-degree angle to touch down smoothly and safely on the runway without bouncing or coming to a sudden stop. Pilots use specialized tools like the Instrument Landing System (ILS) or GPS to stay on the correct path. Lights on the ground, called PAPI lights, help pilots know if they are too high or too low.