Polar Instruments Launches New GRS200 with Extended Troubleshooting for the Repair of Electronic Assemblies
August 2, 2024 | Polar InstrumentsEstimated reading time: 1 minute
The new GRS200 fault locator from Polar Instruments uses the proven passive analogue signature analysis and compares a faultless assembly with the board under test. This method detects typical faults in electronics production, service and repairs quickly and without extensive circuit knowledge.
‘By using the GRS200, missing or reversed components, incorrect component values or component types, counterfeit components as well as short circuits or opens can be recognized very easily,’ says Hermann Reischer, Managing Director of Polar Instruments GmbH. The system consists of analogue signature hardware and powerful software with LIVE signature analysis, program mode and CAD data display. In addition, circuit diagrams, assembly photos, repair reports and an optional digital multimeter may be integrated. For detailed analysis, the system imports more than 20 different formats CAD data, including GenCAD, Hyperlynx, IPC-2581 and ODB++. Furthermore, circuit networks can be graphically highlighted and the associated components displayed.
The nodal impedance test is performed on the unpowered module, whereby a current-limited AC voltage signal generates an impedance signature by measuring voltage and current. The GRS200 system compares the signatures of the defective module with a stored good sample and indicates any noticeable deviations above a defined limit value. As an alternative to the nodal impedance test, an external multimeter can also be integrated into the test process. This allows, for example, voltage and resistance values, frequencies and temperatures to be assigned to defined test points in the CAD layout. It is also possible to locate short circuits on power supply rails and bus lines. An integrated short-circuit locator, in conjunction with the external multimeter, tracks the networks based on the CAD data using a highly sensitive four-wire resistance measurement and tone control. This makes it possible to narrow down the physical position of a short circuit to just a few millimeters.
Within the test program, test points are assigned to circuit networks in the CAD file and their analogue signatures are saved for later comparison. If no CAD data is available, test programs can also be created manually by defining the IC package style and the number of pins.
All test results are documented for traceability. Results for each assembly are recorded in a repair report, providing valuable repair history information. Using an optional USB camera, it is possible to take pictures of an assembly and save them as photo documentation in the test program.
Suggested Items
TRI to Join SMTA Austin Expo 2025
01/16/2025 | TRITest Research, Inc. (TRI), the leading provider of test and inspection systems for the electronics manufacturing industry, is pleased to announce plans to exhibit at the SMTA Austin Expo 2025, scheduled to take place on February 6, 2025, at the Travis County Exposition Center.
Upcoming SMTA UHDI Symposium: Shortening the Learning Curve
01/15/2025 | Marcy LaRont, I-Connect007SMTA’s second annual UHDI Symposium on Jan. 23 in Phoenix will highlight groundbreaking discussions on UHDI assembly test board, innovative electronic inks, process controls, and signal integrity solutions. Organizer Tara Dunn talks about the importance of the event and how she prepared presentations and discussions that would appeal to fabricators, assemblers, and designers. This event will shorten your learning curve and spark new ideas that push the boundaries of hardware electronics manufacturing. There’s still time to register.
Advantest Forms Strategic Partnerships with FormFactor and Technoprobe
01/09/2025 | AdvantestLeading semiconductor test equipment supplier Advantest Corporation announced that it has entered into small minority investments and partnership agreements with both Technoprobe SpA and FormFactor, Inc.
Revolutionizing PCB Testing: RoBAT's Journey from S1 to SCARA
01/07/2025 | Marcy LaRont, PCB007 MagazineFrom the early days of simple continuity testers to the advanced SCARA machines, RoBAT's evolution in time-domain reflectometer (TDR) and test technology is a testament to the company's commitment to excellence and adaptation in a rapidly changing industry. In this discussion, RoBAT’s Bruce Nockton discusses the journey, challenges, and importance of automating testing solutions, and highlights how RoBAT has become a frontrunner in delivering high-precision testing equipment, setting new standards for the industry.
Biden-Harris Administration Awards SRC $285M for New CHIPS Manufacturing USA Institute for Digital Twins
01/07/2025 | U.S. Department of CommerceThe U.S. Department of Commerce announced that CHIPS for America awarded the Semiconductor Research Corporation Manufacturing Consortium Corporation (SRC) $285 million to establish and operate a CHIPS Manufacturing USA institute headquartered in Durham, North Carolina.