Defense Speak Interpreted: It’s Time for a ‘Defense-Speak’ Update
Beyond the Board: The Future of Innovation—Why the Electronics Industry Needs You
American Made Advocacy: New Congress, New Opportunities
Reliability Comparisons of FPBGA Assemblies Under Hot/Cold Biased Thermal Cycle
August 6, 2024 | Thomas Sanders, Seth Gordon, Reza Ghaffarian, Jet Propulsion LaboratoryEstimated reading time: 1 minute
Current trends in microelectronic packaging technologies continue in the direction of smaller, lighter, and higher density packages. The telecommunications industry and particularly mobile/portable devices have a strong need for lighter and smaller products. The current emerging advanced packaging (AP) technologies, including system-in-package (SiP) and 2.5D/3D stacked packaging, added another level of complexity and challenges for implementation. The AP covers a set of innovative technologies that package integrated circuits (ICs) to increase functionality, improve performance, and provide added value1. In contrast, traditional packaging methods cover different I/O density and I/O pitch depending on the targeted application’s requirements, performance, and cost. The AP with heterogeneous integration added additional thermal challenges compared to a single die package2.
For single-die packaging technologies, the density requirement led to a progression in ball-grid-array (BGA) packaging technologies implemented in early 2000. With increased I/O density and decreased package size, the new generation of fine pitch BGA (FPBGA) packages, such as chip scale packages (CSPs) are introduced. A variety of studies have been conducted examining the reliability of printed circuit board assemblies (PCBAs) using BGAs and FPBGAs3-6. Recently, a guideline on BGA and die size BGA (DSBGA) was released for high-reliability applications with consideration of various environmental requirements for a number of NASA mission applications7. There are significant thermal cycle (TC) test data in the range of -55℃ and 125℃, or lower TC ranges, for commercial and even high-reliability applications, which is covered by IPC 97018.
However, thermal cycle test results under extreme cold and cryogenic conditions, representative of deep-space mission applications, is rare. Tudryn et al.9, presented detailed thermal cycle evaluation for Martian environment including die attachment with wire bonds. Recently, Ghaffarian10 and Ghaffarian et al11 compared the low temperature thermal cycles, including -110°C to 20°C for SnPb solder assemblies. The test results covered surface mount technology (SMT) packages including column grid array (CGA) to hand-soldered plated through-hole (PTH) ceramic pin grid array (PGA) assemblies.
To read the entire article, which originally published in the August 2024 issue of the SMT007 Magazine, click here.
Share on:
Suggested Items
IMAPS and DPC: 21 Years of Elevating Technical Knowledge
03/13/2025 | Marcy LaRont, I-Connect007The IMAPS 21st Device Packaging Conference (DPC) may have taken place at a conference center located down an idyllic desert road showcasing the best of what native Arizona has to offer, but the topics at this conference were anything but laid-back. This important platform for professionals in microelectronics and advanced packaging set the stage for a technology in high demand. Brian Schieman, IMAPS executive director, says the show was organized to demonstrate their commitment to addressing current technological trends and with significant energy directed toward fostering connections within the supply chain.
I-Connect007 Editor’s Choice: Five Must-Reads for the Week
03/07/2025 | Andy Shaughnessy, I-Connect007It’s been a busy week. My must-reads include articles and news items on global trends and challenges, groundbreaking technology, the hunt for the elusive young PCB designers, and some personnel changes. We also have a great column on the value of following up and keeping promises. We’re all guilty of “dropping the ball” from time to time, aren’t we?
IMAPS’ Annual Conference Opener in Phoenix ‘Blew My Mind’
03/05/2025 | Marcy LaRont, I-Connect007It was a cool and sunny morning as I headed out to the IMAPS Device Packaging Conference 2025 in Arizona early Tuesday, which featured two compelling keynote speakers, and a day chocked full of technical sessions. IMAPS 2025 also hosted a sold-out exhibit hall with 65 exhibitors from IBM and Heraeus to Cadence and KYZEN, to name just a few. The technology and packaging discussions at this conference blew my mind last year, and it is clear this year would be no different.
2025 IEEE Electronic Components and Technology Conference
03/04/2025 | IEEEMore than 2,000 scientists, engineers and businesspeople are expected to attend the 75th annual IEEE Electronic Components and Technology Conference (ECTC) from May 27-30, 2025 at the Gaylord Texan Resort & Convention Center here.
Ennostar Consolidates Resources to Drive High-Value Optical Semiconductors Applications in 3+1 Key Areas
02/25/2025 | TrendForceIn an effort to optimize its organizational structure and accelerate its optical semiconductors business, Ennostar announced on February 21st, 2025, the merger of its subsidiaries—Epistar and Lextar Electronics—under the unified brand of Ennostar Corporation.