Flexible Thinking: Rules of Thumb—A Word to the Wise
Happy’s Tech Talk #29: Bend-to-Install Semi-flex FR-4
Connect the Dots: Five Best Practices for Designing Flex and Rigid-flex PCBs
DELO: New Semicon Adhesive Propels Autonomous Driving Forward
October 20, 2023 | DELOEstimated reading time: 1 minute
DELO has developed a flexible electronics adhesive that permanently seals sensor housings airtight and thus reliably protects components such as image sensors. DELO DUALBOND BS3770 meets the stringent requirements of the semiconductor and automotive industries and helps drive innovation in autonomous driving.
The autonomous driving trend comes with ever-stricter safety requirements. Therefore, reliable components such as image sensors are installed in LiDAR and RADAR systems. Sensor housings on PCBs must be hermetically sealed throughout their entire service life in order to maintain their function permanently without interruption. However, previous solutions for hermetically sealing the housing and filter glass are reaching their limits due to these stricter requirements, failing to withstand the tests of the automotive industry, according to standard AEC-Q100.
DELO has developed DELO DUALBOND BS3770, a special electronics adhesive for semiconductor manufacturers to meet the demanding reliability and qualification tests of automotive suppliers.
Unlike adhesives previously available on the market, the newly developed adhesive is a flexible product with a Young's modulus of less than 5 MPa at room temperature. Due to its flexible properties starting from a temperature as low as approximately -50 °C, the adhesive can compensate for pressure changes that occur, such as those caused by temperature changes, humidity differences, or heat input in the reflow process during production. As a result, defects such as pop-ups or delamination do not occur, and the sensor is permanently protected.
DELO DUALBOND BS3770 can be precisely applied by needle dispensing while maintaining narrow and high bondlines. Curing takes place in two consecutive steps using UV light and heat. After dispensing, the adhesive is fixed in a few seconds by means of classic light fixation. Alternatively, it can be transferred to the B-stage, which is particularly relevant for bonding filter glasses with blackprint. At this stage, it achieves an initial adhesion comparable to tape. Afterwards, the second component can be joined. Thanks to the adhesive’s initial adhesion, the component is directly fixed so that it can be entirely processed further. Final curing takes place in a convection oven at +150 °C within 40 minutes.
In addition to image sensors for LiDAR and RADAR applications, DELO DUALBOND BS3770 is also used in driver monitoring and for 5G applications.
Share on:
Suggested Items
Satellite Communications to Improve Connectivity in Remote Areas
11/27/2024 | UK Space AgencyDespite the significant progress made on superfast and gigabit-capable broadband, certain remote and rural locations across the UK still face challenges where satellites offer the only practical solution for connectivity.
Siemens’ Solido SPICE Now Certified for Multiple Leading-edge Samsung Foundry Processes
11/27/2024 | Siemens Digital Industries SoftwareSiemens Digital Industries Software announced that its continued collaboration with longtime customer Samsung Foundry has established a host of new certifications for its recently introduced Solido™ SPICE software, which supports the verification of next-generation analog, mixed-signal, RF, memory, library IP and 3D-IC semiconductor designs.
Biden-Harris Administration: CHIPS Incentives Award with Intel to Advance U.S. Leading-Edge Chip Capacity
11/27/2024 | U.S. Department of CommerceThe Biden-Harris Administration announced that the U.S. Department of Commerce awarded Intel Corporation up to $7.865 billion in direct funding under the CHIPS Incentives Program’s Funding Opportunity for Commercial Fabrication Facilities. The award follows the previously signed preliminary memorandum of terms, announced on March 20, 2024, and the completion of the Department’s due diligence.
Koh Young Technology Showcasing Advanced Packaging Inspection Solutions at SEMICON Japan at Tokyo Big Sight
11/26/2024 | Koh Young TechnologyKoh Young Technology, the global leader in True 3D measurement-based inspection solutions, will demonstrate its award-winning inspection solutions in Hall 1 Booth 1310 at Tokyo Big Sight on December 12-13, 2024.
Is It the Death of the Dashboard?
11/27/2024 | Nolan Johnson, SMT007 MagazineIn 2024, companies are leveraging AI agents to automate data-driven decisions, bypassing the need for specialized data science skills. In this interview with Tim Burke and Jennifer Davis of Arch Systems, they say these AI tools can handle straightforward tasks, significantly improving factory efficiency by addressing numerous small issues. This shift allows existing staff to use data effectively without extensive retraining. Both large and small language models are used to support real-time decisions on the production floor, integrating various data sources to create a comprehensive digital twin of the factory’s operations.